Gluon v2019.1.x will be the last series of releases to support batman-adv-legacy (v14 compat) and IBSS (Ad-hoc) mesh links. Migration features have been developed and should be used during this release cycle to migrate to batman-adv v15 compat and/or 802.11s mesh links. These migration features are the scheduled domain switching (since v2018.2.1) and batman-adv module coexistence (since v2019.1, see below). The migration must be completed before an upgrade to future Gluon releases (v2019.2 or later) becomes possible.
With Gluon v2019.1, nodes will not answer respondd queries on
[ff02::2:1001]:1001 anymore. Respondd
querier setups still using this address must be updated to the new address
(supported since Gluon v2017.1). This change was required due to cross-domain leakage of respondd data.
If you are upgrading from a version prior to v2018.1, please note that the flash layout on some devices (TP-Link CPE/WBS 210/510) was changed. To avoid upgrade failures, make sure to upgrade to Gluon 2017.1.8 or the latest Gluon 2016.2.x (unreleased) before installing Gluon 2018.1, 2018.2 or 2019.1.
Added hardware support¶
- DAP-1330 A1
- RT-AC57U 
|||This target will be reaching its end of life soon. This means that support in the next major release of Gluon is doubtful.|
|||This is a new target.|
|||Device or target does not support AP+IBSS mode: This device or target will not be built
when GLUON_WLAN_MESH is set to |
ipq806x target has been flagged as broken, as none of its devices are fully supported in this OpenWrt
release yet. You might have to update your build scripts accordingly.
To allow a migration from B.A.T.M.A.N. Adv. compat 14 this Gluon release offers the ability to ship both
B.A.T.M.A.N. Adv. compat versions 14 and 15 in the same image. The
mesh.batman_adv.routing_algo option is used
to decide which module gets loaded and the scheduled domain switching functionality can be used to migrate between
the two versions.
Note that if you were using
gluon-mesh-batman-adv-14 (“batman-adv-legacy”) before you will need to update the
mesh.batman_adv.routing_algo setting from
BATMAN_IV_LEGACY if you want to
stay on v14 compat.
See the mesh section for the site.conf configuration of this feature.
Radio devices hosted outdoors are often affected by different regulation than if they were installed indoors. The
outdoor mode allows for the reconfiguration of 5 GHz radios onto different channels and channel ranges.
Regulatory policies like DFS currently make it difficult to use the 5 GHz band for mesh networking because it’s
never certain that nodes will stay on the same channel.
If enabled, by setting
wifi5.outdoor_chanlist, a number of devices that are commonly installed outdoors will
have outdoor mode automatically enabled during their initial setup, specifically:
- Bullet M
- Litebeam M5
- Nanostation M5
- Nanostation M5 Loco
- Rocket M5
- Rocket M5 TI
- Unifi AC Mesh
- Unifi AC Mesh Pro
- Unifi Outdoor
See the wifi5 section for the site.conf configuration of this feature.
The ar71xx-tiny and several devices in the ramips-rt305x target have been marked as deprecated. The GLUON_DEPRECATED flag was introduced to offer communities the choice on how to deal with the ending support for those devices. Devices or targets marked as deprecated will very likely not be included in following Gluon releases anymore, usually due to their insufficient flash size.
See the Build configuration section for details.
Hoodselector: Geolocation Mode¶
The new hoodselector package allows a node to automatically reevaluate its selected mesh domain at runtime. In this release we support its geolocation feature.
See the gluon-hoodselector documentation for details.
x86 images support firstboot¶
x86 images are now using squashfs instead of ext4 and can now have their configuration reset by using
- Fixes passwordless SSH access when gluon-authorized-keys was used without gluon-setup-mode. (#1777)
- Fixes cross-domain leakage of respondd data by not joining the link-local multicast group on br-client. Nodes will
not be answering respondd queries on
[ff02::2:1001]:1001anymore. Respondd queries using that address must be updated to the new address
When updating a site configuration from Gluon 2018.2.x, the following changes must be made:
- We now require the
GLUON_DEPRECATEDvariable to be set to decide how to handle the image generation for deprecated devices. (#1745)
- The variable
DEVICESthat controls which devices to build images for has been renamed to
gluon-radvdpackage is now included by default and can be dropped from FEATURES and GLUON_SITE_PACKGES.
mesh.batman_adv.routing_algooption is now required when the batman-adv routing protocol is used. (#1622)
To continue using batman-adv v14 compat you need to set this option from
wifi*.supported_rateshave been removed, as the legacy 802.11b rates are now disabled by default. (#1716)
These are recommendations for running non-Gluon nodes, like for example gateways, in your mesh network:
Since Gluon v2018.1 the IGMP/MLD segmentation feature was enabled by default. When
bat0is run with a bridge on top the
bat0bridge port should be set to receive all multicast traffic unconditionally:
# echo 2 > /sys/class/net/bat0/brport/multicast_router
See the chapter on IGMP/MLD Domain Segmentation for more details.
Debug Build Flag¶
GLUON_DEBUG=1 will provide firmware images including debugging symbols usable with GDB or similar tools.
Requires a device or target with at least 16 MB of flash space, e.g. x86-64. Unset by default.
Lua target files¶
Target definitions were rewritten in Lua; this was necessary to implement the device deprecation feature. It also offers the option for more flexible tagging of devices in the future. (#1745)
Lua scripts can now be properly linted and analyzed using luacheck. Run
luacheck package scripts target in the
Gluon project root. (#1741)
Out of memory situations with high client count on ath9k. (#1768)
The integration of the BATMAN_V routing algorithm is incomplete.
- Mesh neighbors don’t appear on the status page. (#1726)Many tools have the BATMAN_IV metric hardcoded, these need to be updated to account for the new throughputmetric.
- Throughput values are not correctly acquired for different interface types.(#1728)This affects virtual interface types like bridges and VXLAN.
Default TX power on many Ubiquiti devices is too high, correct offsets are unknown (#94)
Reducing the TX power in the Advanced Settings is recommended.
The MAC address of the WAN interface is modified even when Mesh-on-WAN is disabled (#496)
This may lead to issues in environments where a fixed MAC address is expected (like VMware when promiscuous mode is disallowed).
Inconsistent respondd API (#522)
The current API is inconsistent and will be replaced eventually. The old API will still be supported for a while.
Frequent reboots due to out-of-memory or high load due to memory pressure on weak hardware especially in larger meshes (#1243)
Optimizations in Gluon 2018.1 have significantly improved memory usage. There are still known bugs leading to unreasonably high load that we hope to solve in future releases.