gluon-mesh-batman-adv

../_images/gluon-mesh-batman-adv-logo.svg

B.A.T.M.A.N. Advanced (often referenced as batman-adv) is an implementation of the B.A.T.M.A.N. routing protocol in form of a linux kernel module operating on layer 2.

Layer 2 means that all client devices will operate in the same, virtual broadcast domain and will see each other “as if they were connected to one giant switch”.

This comes with a set of advantages (like quick and economical client device roaming, layer 3 protocol agnosticism, broadcast/multicast). But also impediments, especially layer 2 multicast overhead - which Gluon tries to mitigate to achieve a certain degree of scalability. See gluon-ebtables-filter-multicast and Multicast Architecture for details.

B.A.T.M.A.N. Advanced project homepage:

Flavours

Gluon currently supports two main build flavours of batman-adv:

gluon-mesh-batman-adv-15

This is the recommended batman-adv flavour to use.

It follows recent, upstream batman-adv releases and is flexible to new feature additions.

gluon-mesh-batman-adv-14 (batman-adv-legacy)

gluon-mesh-batman-adv-14, also known as batman-adv-legacy or batman-adv v2013.4 is the last batman-adv release with the batman-adv compatibility version 14, which was released in October 2013.

With batman-adv v2014.0.0 a compat breakage became necessary for the introduction of new features. However, one of these features was the addition of TVLV support (type-version-length-value fields) which from then on allowed adding features without breaking packet format compatibility. This made it possible to stay with compatibility version 15 so far.

For new installations gluon-mesh-batman-adv-14 is not recommended. It misses a lot of bugfixes and is currently only available for existing communities until they have migrated. This package will soon be deprecated and removed.

Also see:

B.A.T.M.A.N. Routing Algorithms

For the gluon-mesh-batman-adv-15 package two routing algorithms are selectable via site.conf mesh section: BATMAN_IV and BATMAN_V.

For the gluon-mesh-batman-adv-14 package, BATMAN_IV_LEGACY needs to be selected.

BATMAN_IV - stable

This is the recommended algorithm to use with gluon-mesh-batman-adv-15.

BATMAN_V - experimental

This is the experimental B.A.T.M.A.N. routing algorithm. It is packet format / compatibility stable but is still in development.

For more details, see:

Multicast Architecture

../_images/gluon-mesh-batman-adv-multicast.svg

While generally broadcast capability is a nice feature of a layer 2 mesh protocol, it quickly reaches its limit.

For meshes with about 50 nodes / 100 clients, or more it is therefore highly recommended to add the gluon-ebtables-filter-multicast package. Also, with gluon-mesh-batman-adv-15 or gluon-mesh-batman-adv-14 installed gluon-ebtables-limit-arp is selected by default.

Furthermore, by default IGMP and MLD messages are filtered. See site.conf mesh section and IGMP/MLD Domain Segmentation for details.

To achieve some level of scalability for multicast, multicast group awareness is implemented and utilized in the following ways:

Node-Local Multicast Handling

../_images/gluon-mesh-batman-adv-multicast-architecture-to-clients.svg

A Gluon node sends IGMP/MLD Queries with the following parameters on its local segment:

  • Interval: 20 seconds
  • Robustness: 9
  • Query Response Interval: 5 seconds

This way, through the returning IGMP/MLD reports, the node learns which multicast groups its clients are interested in.

This is then used to deliver multicast packets to its own Wifi clients via individual Wifi unicast transmissions instead of a broadcast transmission.

The advantages of this are:

  • Usually higher bitrates: Mostly lower airtime usage
  • Acknowledged, retried transmissions (ARQ): Higher reliability
  • If no local client is interested: Avoiding the transmission, no airtime usage

Notably multicast for IPv6 Neighbor Discovery usually has only a single multicast listener in the case of address resolution and usually no multicast listener for duplicate address detection. Which are the ideal cases for multicast snooping / multicast to unicast.

The unicast delivery is achieved through utilizing the multicast-to-unicast feature in OpenWrt/netifd. Which in turn utilizes the multicast-to-unicast conversion and hairpin features of the Linux bridge, plus the hostapd client isolation feature, to hand over full delivery control to the bridge.

Mesh-wide Multicast Handling

../_images/gluon-mesh-batman-adv-multicast-architecture-to-mesh.svg

To be able to avoid transmissions not only on the “last mile”, the AP interface to the local clients, but also from the “last mile” into the mesh in the future multicast listener state is propagated through the mesh:

batman-adv (compat 15) taps into the Linux bridge and inherits the multicast groups into its translation table. Which then takes care of efficiently distributing this knowledge to other nodes.

While by that the receiver side is ready to go, the sender part in batman-adv is disabled for now in Gluon. It will be enabled in a future release.

IGMP/MLD Domain Segmentation

../_images/gluon-mesh-batman-adv-multicast-architecture-segmentation.svg

Internet Group Membership Protocol and Multicast Listener Discovery Protocol are the standardized network protocols to query, report and learn multicast group memberships on the local link for IPv4 (IGMP) and IPv6 (MLD).

By default Gluon filters IGMP and MLD queries and reports towards the mesh and runs an IGMP/MLD querier on each node for its own local clients. Furthermore Gluon tags the mesh side bridge port (bat0) as a multicast router port.

That way, even though the Linux client bridge in Gluon is unable to learn about multicast memberships behind other nodes, the multicast router port flag will force it to unconditionally hand over all multicast packets to batman-adv. Which even with IGMP/MLD filtered, will have full multicast membership knowledge through its own propagation through the batman-adv translation table.

Advantages are:

  • Reduced overhead through reactive batman-adv multicast TT vs. periodic IGMP/MLD messages in the mesh
  • Increased IGMP/MLD snooping robustness via local, per node IGMP/MLD queriers
  • DDoS vector mitigation

Note: For nodes running an operating system other than Gluon, but a bridge interface on top of the batman-adv interface, you will need to set the multicast router flag there manually:

debian$ echo 2 > /sys/class/net/bat0/brport/multicast_router

“2” for this parameter means to always assume a multicast router behind this bridge port and to therefore forward all multicast packets to this port. Versus the default of “1” which means to learn about multicast routers via IGMP/MLD Queries, PIM and MRD messages; or “0” to always assume that there is no multicast router behind this port, meaning to only forward multicast to this port if an according multicast listener on this link was detected.

Further limitations: IGMP/MLD snooping switches (e.g. “enterprise switches”) behind the client network of a node (LAN ports) are unsupported. It is advised to disable IGMP/MLD snooping on those enterprise switches for now or to at least manually mark the port to the Gluon router as a “multicast router port”.

Alternatively, the filtering of IGMP/MLD reports can be disabled via the site.conf (which is not recommended in large meshes though). See site.conf mesh section for details.